Glue Rigid Plates - Practical Tips for Proper Attachment

Glue Rigid Plates - Practical Tips for Proper Attachment

There are many ways to dress up bare walls, to give them a pleasant and handsome look. This often includes the application of wallpaper or plastering. A much less expensive method is the plasterboard or plasterboard. Rigips is a brand name and not the product name. But these are plates that can be cut to size. There are other important preparations that need to be done carefully for a good result.

What preparations are and how the plasterboard will be glued later is explained in the following paragraphs.

Benefits of Rigips

Rigips is generally considered a very versatile building material, which is available in various designs. In the form of plates, it can be cut to any size. In addition, there are advantages in the low weight. This not only makes the work easier, but also loads the walls very little. In combination with a substructure, the boards are also well suited for cladding various lines. In principle, there are special plates for different applications. These include, for example, panels that are suitable for use in wet rooms, as well as panels with special fire protection.

Conventional plasterboard should be protected from excessive moisture. Rigips provides a breeding ground for mildew.

Preparing the Walls

It's a good idea to clean up any coarser bumps. If there are still small dents or the like, that's not bad. Significantly more important is that previously plastered walls, no loose plaster remains. These can later ensure that the plates do not hold. For this, it is usually advisable to remove the entire plaster, otherwise other sites start to break out. Another important step is the measurement of the walls. However, the later thickness of the boards should be taken into account later in order to avoid problems in the corner areas. After measuring, it is advisable to cut the boards. As a result, this step does not have to be performed until the adhesive is already on the walls.

Mixing and Applying Plaster Adhesive

In principle, when mixing the adhesive, follow the manufacturer's instructions. But there are still some helpful tips. The mixing ratio can best be maintained if a balance is used for water and gypsum. In addition, the water should have room temperature as possible. For stirring is suitable a stirrer. With this, the gypsum can then be stirred slowly, if possible without interfering with air bubbles. The finished plaster is very creamy and is then applied in thick dabs. He comes not only on the wall but also on the plate. The advantage with Kleksen is the possibility to compensate for unevenness on the wall. This works better if the Klekse are thicker. However, the measured size should always be taken into account.

Only so much gypsum should be mixed at the same time as it can be processed so that it does not dry before it is used.

Gluing the plates

The plates are pressed against the wall. A spirit level should be used to ensure a smooth application. This applies to horizontal as well as vertical alignment. A lot can also be used well. When pressed, there should be enough fingertip feel to press the plates tight enough and leave enough room to align. On the ceiling and on the floor it is often helpful to make small joints by attaching small wedges. This process is then repeated until all the plates are evenly aligned and attached. It is usually very helpful to start at the bottom and place the top rows offset. The glue then has to dry afterwards.

Post-processing of plates

If the entire wall is nested with the plates, post-processing can begin. Of course, the different plates create small joints between the individual plates. Therefore, they should be filled. For plastering is again plaster, but can be inquired in any case in the hardware store, which material is well suited for the respective plates. After grouting, it often makes sense to sand the dried material. As a result, excess residues are also removed. The joints on the floor and ceiling should be grouted with silicone or something similar to get a better seal in these areas. If the result is then really evenly smooth, you can continue working. This includes the painting or wallpapering of the plates. Especially for painting, it is important to have a completely smooth surface.

Possible sources of error

There are many possible sources of error. This especially includes moisture. This applies to the plates but also to the underlying wall. It is important to make sure that the wall is really dry. In case of doubt, a professional should rather be contacted and inquired there. Also, be careful when mixing the adhesive, as the adhesive must not be too liquid. If too much water is mixed in, the glue loses its important adhesive power.

Conclusion

Rigips or gypsum plasterboards are an easy way to wall walls. Overall, it is a material that is very susceptible to moisture. However, the big advantage lies in the low weight, which makes it possible to equip non-load-bearing walls.

Summary

After the walls have been prepared, the glue can be mixed. The glue can then be used to attach and accurately align the cut sheets. Then the joints have to be filled before painting can begin.

Artikelbild: © forestpath / Shutterstock



Got mysql Error: Disk full (/var/tmp/#sql_5b37_0); waiting for someone to free some space...
in querySELECT a.id, a.id_category, a.id_tag, a.template, a.url, a.h1, a.h2, a.h3, a.stext, a.text, a.img , img_bing FROM en_content a left join en_cat_content tc on (a.id = tc.article_id) where tc.cat_id in ( 11 ) AND a.id <= 1153 group by a.id DESC LIMIT 0, 1