Parquet oiled - so the parquet is given a new shine

Parquet oiled - so the parquet is given a new shine

The parquet floor can be oiled for several reasons. First and foremost, it is suitable for renovating the worn floors. Old and worn floors can acquire a new shine without having to be replaced. In addition, it is also possible to upgrade freshly laid soils right from the start. This has two advantages. On the one hand, the floors get a certain shine right from the start, and on the other hand, the look of the floors can be permanently maintained if the oil is renewed when needed. In addition, the floor is also sealed.

Tips on how to lay the parquet correctly and how to oil the parquet floors are described in the following text.

Laying Parquet Floors

As the parquet floors are also oiled immediately after firing Laying makes sense, is also shown how the parquet floors are laid. First of all, a layer of insulating material should be laid. This usually dampens the steps. Afterwards the parquet can already be laid. For this purpose, a distance between wall and parquet is made with small wedges. The parquet is then laid in rows by clicking the parquet together. This is usually relatively easy in the front row and only becomes more complicated in the following rows. However, there too, the parquet only has to be clicked one after the other on the sides. This process is then repeated until the entire floor is occupied.

Preparing to oil the parquet floor

Whether the parquet floor has been recently laid or renovated, the first step in the preparation process should always be to make the entire surface accessible. Afterwards, the floor must then be sanded with special sanding machines. It is essential to use the right machines for the respective types of wood. This process should be carried out as thoroughly as possible, otherwise the subsequent result will not be optimal. When grinding, the joints can also be filled with appropriate materials at the same time. After sanding, the floor should then be vacuumed to remove any residue and dust.

Since direct sun light affects the oil, the windows should be darkened. Therefore, it makes sense to perform electrical installations prior to oiling the parquet so that light sources can be used.

Applying the Oil

When the room is properly prepared, application of the oil can begin. For this purpose, the oil must first be mixed so that it is a uniform mass. Then the oil can be applied evenly. If the areas are large, it makes sense to divide them into sections. Applying should be done without interruption, however, even application is equally important.

After applying the right amount, the oil should be smoothed relatively quickly to prevent puddles. The puddles waste material on one side and are also not good for the wood. Smoothing can be done with a trowel. A brush can then be used in the corners.

The correct amount of oil for each surface is usually indicated on the packaging. If the area is smaller than the possible area of ​​the oil, the amount can be easily converted.

Post-parquet finishing

After the oil has been applied and smoothed, it should be checked if the wood is already saturated and if the wood is saturated Saturation is regular. If this is not the case, oil can be applied again to the individual points. After application, the oil can move in for less than a quarter of an hour. Then excess oil should be wiped off. For this purpose, a rag without lint should be used, as they otherwise work into the oil. The process can also be performed a second time, as in some cases, renewal may not be so frequent.

After the last process has been repeated, it takes 24 hours for the floor to be accessible and 48 hours to set up furniture. However, it is essential to observe the manufacturer's instructions. Until then, however, the room should be ventilated.

Choosing the right oil

When choosing the right oil, it depends on the type of wood and the size of the room. However, the size of the room usually only determines the package size of the oil. It is also important how many layers should be applied. The type of oil depends on the desired effect, but especially on the type of wood. Again, there are oils that indicate on the packaging what the oil is suitable for. In addition, the respective oil in the sequence also determines how often the oil must be renewed if the effect is to persist.

Conclusion

The oiling of the soil is first and foremost for visual reasons meaningful and can therefore already from the beginning on freshly laid floors. However, this technique is useful even if the floor has lost the old shine. This applies both to previously oiled floors as well as to those that have not yet received such treatment.

Summary

Before the parquet floor can be oiled, it must be sanded down. The oil must then be applied regularly so that it can move in. The oiling of the soil cares for it and lends it shine for a long time.

Artikelbild: © mr. Smith / Bigstock.com


Search